twitter
Search
Sunday
Feb192012

Sparkfun RGB LED and RGB Light Sensor

I can't quite figure this one out: it's VERY delicate and I can't get consistant color results with the built-on LED on or off. I know if it gets a UV light, it shows a lot of purple and if it gets hit with a red laser it maxes out the red LED. Anyhow... Video and code! 

 

 

/*
Expanded to use the Sparkfun RGB LED on pins 3, 5, and 6, sending
PWM signals as 1/10 of the result. YouTube video of this in action at
Use of the RGB LED changes added by thoughtfix 2/2012
Inherited OSHW license.
Original comments below.
*/
/*
An Arduino code example for interfacing with the 
HDJD-S822-QR999 Color Sensor.  Put an object in front of the
sensor and look at the serial monitor to see the values the sensor
is reading.  Scaling factors and gains may have to be adjusted
for your application.
by: Jordan McConnell
 SparkFun Electronics
 created on: 1/24/12
 license: OSHW 1.0, http://freedomdefined.org/OSHW
 
Connect the gain pins of the sensor to digital pins 7 - 12 (or ground).
Connect the led pin to digital 13.
Connect Vr to analog 0, Vg to analog 1, and Vb to analog 2.
*/
// Define pins
const int ledpin = 13;
const int GSR1 = 12;
const int GSR0 = 11;
const int GSG1 = 10;
const int GSG0 = 9;
const int GSB1 = 8;
const int GSB0 = 7;
const int redLed = 3;
const int greenLed = 5;
const int blueLed = 6;
int redpin = A0;
int greenpin = A1;
int bluepin = A2;
// Sensor read values
int red = 0;
int green = 0;
int blue = 0;
int redBright = 0;
int greenBright = 0;
int blueBright = 0;
void setup() 
{
  Serial.begin(9600);
  pinMode(ledpin, OUTPUT);
  pinMode(GSR1, OUTPUT);
  pinMode(GSR0, OUTPUT);
  pinMode(GSG1, OUTPUT);
  pinMode(GSG0, OUTPUT);
  pinMode(GSB1, OUTPUT);
  pinMode(GSB0, OUTPUT);
  pinMode(redLed, OUTPUT);
  pinMode(greenLed, OUTPUT);
  pinMode(blueLed, OUTPUT);
  // Turn on the LED
  digitalWrite(ledpin, LOW);
  
  // Set the gain of each sensor
  digitalWrite(GSR1, LOW);
  digitalWrite(GSR0, LOW);
  digitalWrite(GSG1, LOW);
  digitalWrite(GSG0, LOW);
  digitalWrite(GSB1, LOW);
  digitalWrite(GSB0, LOW);
}
void loop() 
{
  
  // Read sensors
  // On page 7 of the datasheet, there is a graph of the 
  // spectral responsivity of the chip.  Scaling factors were
  // selected based on this graph so that the gain of each 
  // color is closer to being equal
  red = analogRead(redpin) * 10;
  green = analogRead(greenpin) * 14;
  blue = analogRead(bluepin) * 17;
  redBright = red/10;
  greenBright = green/10;
  blueBright = blue/10;
  // Print values to the serial monitor
  Serial.print("Red: ");
  Serial.print(red, DEC);
  analogWrite(redLed, redBright);
  Serial.print("\t\tGreen: ");
  Serial.print(green, DEC);
  analogWrite(greenLed, greenBright);
  Serial.print("\tBlue: ");
  Serial.println(blue, DEC);
  analogWrite(blueLed, blueBright);
  delay(20);
}
/*Expanded to use the Sparkfun RGB LED on pins 3, 5, and 6, sendingPWM signals as 1/10 of the result. YouTube video of this in action at
Use of the RGB LED changes added by thoughtfix 2/2012Inherited OSHW license.Original comments below.*/
/*An Arduino code example for interfacing with the HDJD-S822-QR999 Color Sensor.  Put an object in front of thesensor and look at the serial monitor to see the values the sensoris reading.  Scaling factors and gains may have to be adjustedfor your application.
by: Jordan McConnell SparkFun Electronics created on: 1/24/12 license: OSHW 1.0, http://freedomdefined.org/OSHW Connect the gain pins of the sensor to digital pins 7 - 12 (or ground).Connect the led pin to digital 13.Connect Vr to analog 0, Vg to analog 1, and Vb to analog 2.*/

// Define pinsconst int ledpin = 13;const int GSR1 = 12;const int GSR0 = 11;const int GSG1 = 10;const int GSG0 = 9;const int GSB1 = 8;const int GSB0 = 7;const int redLed = 3;const int greenLed = 5;const int blueLed = 6;
int redpin = A0;int greenpin = A1;int bluepin = A2;
// Sensor read valuesint red = 0;int green = 0;int blue = 0;int redBright = 0;int greenBright = 0;int blueBright = 0;
void setup() {  Serial.begin(9600);
  pinMode(ledpin, OUTPUT);  pinMode(GSR1, OUTPUT);  pinMode(GSR0, OUTPUT);  pinMode(GSG1, OUTPUT);  pinMode(GSG0, OUTPUT);  pinMode(GSB1, OUTPUT);  pinMode(GSB0, OUTPUT);  pinMode(redLed, OUTPUT);  pinMode(greenLed, OUTPUT);  pinMode(blueLed, OUTPUT);
  // Turn on the LED  digitalWrite(ledpin, LOW);    // Set the gain of each sensor  digitalWrite(GSR1, LOW);  digitalWrite(GSR0, LOW);  digitalWrite(GSG1, LOW);  digitalWrite(GSG0, LOW);  digitalWrite(GSB1, LOW);  digitalWrite(GSB0, LOW);}
void loop() {    // Read sensors  // On page 7 of the datasheet, there is a graph of the   // spectral responsivity of the chip.  Scaling factors were  // selected based on this graph so that the gain of each   // color is closer to being equal  red = analogRead(redpin) * 10;  green = analogRead(greenpin) * 14;  blue = analogRead(bluepin) * 17;  redBright = red/10;  greenBright = green/10;  blueBright = blue/10;
  // Print values to the serial monitor  Serial.print("Red: ");  Serial.print(red, DEC);  analogWrite(redLed, redBright);  Serial.print("\t\tGreen: ");  Serial.print(green, DEC);  analogWrite(greenLed, greenBright);  Serial.print("\tBlue: ");  Serial.println(blue, DEC);  analogWrite(blueLed, blueBright);  delay(20);}

 

PrintView Printer Friendly Version

EmailEmail Article to Friend

Reader Comments

There are no comments for this journal entry. To create a new comment, use the form below.

PostPost a New Comment

Enter your information below to add a new comment.

My response is on my own website »
Author Email (optional):
Author URL (optional):
Post:
 
All HTML will be escaped. Hyperlinks will be created for URLs automatically.
« R2-D2 Laser Robot for Cats | Main | Adafruit Circuit Playground »